This conversion frame is installed when converting from the original HS2000 series valves to HS4000 valves. The conversion frame is used as an alternative to sheetrock repair. For conversion, 1-HS3000 Rough-In Kit, 1-HS4000 trim kit, and 1-conversion frame are required. Available in white (HS300051) or almond (HS300052). Refer to HAH Trim Conversion Installation Guide.
The white end cap fits into the end of a Hide-A-Hose Rapid Flex Hose, keeping the end of the hose round. (Black and white end caps are NOT interchangeable).
Hose sock replacement kits include a hose sock pre-loaded on a cardboard tube and a tension guide for ease of installation. Refer to Hose Sock Replacement Instructions.
NOTE: This item should only be used to replace the hose sock on a SmartSock hose and is Not for use on a Rapid Flex hose. The RapidFlex hose is a larger diameter than the SmartSock hose.
HS3000 Rough-In Frame is required for the HS4000 Valve new construction or retro-fit installations. The Rough-In Kit includes: 1 rough in frame, 1 rough in pipe fitting, 1 reducer, 1 mud cover, 1 retainer band, 4 mud cover screws. Refer to HS4000 installation guide for mounting instructions.
HS4000 Valve Sleeve Replacement Kit includes a Top Cap, Rubber Sleeve, six screws, and an instruction sheet. This replacement kit can be used for either HS3000 or HS4000 valves. (Before removing the valve from the wall, the whole hose must be removed from the valve).
The Valve Trim Kit includes: inlet valve, finish door, low voltage switch, 4 screws, 2 wire nuts, 1 silicone pack. Available in white, almond, or black. Refer to HS4000 installation guide for valve trim instructions.
This Rough-In Frame is required for HS5000 new construction or retro-fit installations (exception: installation with concrete wall kit). The Rough In Kit includes: 1 rough in frame, 1 rough in pipe fitting, 1 reducer, 1 mud cover, 4 mud cover screws.
The Valve Trim Kit includes: inlet valve, finish door, low-voltage switch, 4 screws, 2 wire nuts. New features include smaller size, improved rubber door seal, improved hose-locking system, simple on/off switch, adjusts to wall thicknesses up to 1 ½ inches (3.8 cm). Available in white or almond. Refer to HS5000 installation guide for valve trim instructions.
The Hide-A-Hose Mini Valve is a cost effective quick-clean solution designed for laundry rooms, master bathrooms, or garages. This valve is 20% smaller than the full featured HS5000 valve. The Mini Valve does not have a locking mechanism so the hose must be pulled all the way out to make a lock and seal. This Mini Valve Garage Kit comes with a Rough-In Frame, Hide-A-Hose Mini Valve, and a 22 ft hose.
The Hide-A-Hose Mini Valve is a cost effective quick-clean solution designed for laundry rooms, master bathrooms, or garages. This valve is 20% smaller than the full featured HS5000 valve. The Mini Valve does not have a locking mechanism so the hose must be pulled all the way out to make a lock and seal. This Mini Valve Garage Kit comes with a Rough-In Frame, Hide-A-Hose Mini Valve, and a 40 ft hose.
Rapid Flex central vacuum hoses are made of scratch resistant material that does not require a hose sock. Rapid Flex hoses pull out more easily and retract faster than hose kits, and are a larger diameter, increasing air flow 20 -30%. Our new Rapid Flex hoses feature the mini-cuff, which allows tools to fit directly onto the hose cuff for easier use. Hose lengths can be customized to fit the home-owner’s needs. Trim desired length from end of hose that goes in valve first, then replace end cap into trimmed end (Do not trim the cuff-end of hose).
The Hide-A-Hose RapidFlex Mini-Cuff connects the hose to a Ready Grip Direct Connect handle.
The Mini-Cuff also offers the convenience of connecting directly to accessories included in the tool kits.
This cuff is 1 3/8” and will only fit the Rapid Flex hose. (See HS5000H4 for a SmartSoc hose cuff.)
The mini-cuff acts as a stop when the hose is retracted into the valve. If the cuff comes off the hose, screw the cuff back into the hose, counterclockwise, until it is firmly seated against the end of the hose. If the end of the hose has been damaged, trim off 2” – 3” with sharp scissors before installing the new cuff. Do not retract the hose without the cuff.
(If additional friction is needed to hold the hose in place when closing the valve door, the mini-cuff accepts 1 or 2 O-Rings. See Part#HS500123)